"Si-6" : 16 results

Si-6 series

http://www.toyo-mm.co.jp/english/pro/servo-motor-driven-injection/si-6.html
>> Si-30-6EP series Features Si-6 series Features The Si-6 series provides a SMART solution to ever-complicate Read more...

CS series

http://www.toyo-mm.co.jp/english/pro/fully-electric-injection-molding-machine-changshu/cs.html
CS series Features NEW Fully Electric Injection Molding Machine produced at our Changshu factory for further m Read more...

Si-50-6Si-50-6

http://www.toyo-mm.co.jp/english/product/spec/415.htmlhttp://www.toyo-mm.co.jp/english/product/spec/415.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

Si-80-6Si-80-6

http://www.toyo-mm.co.jp/english/product/spec/416.htmlhttp://www.toyo-mm.co.jp/english/product/spec/416.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

Si-100-6Si-100-6

http://www.toyo-mm.co.jp/english/product/spec/417.htmlhttp://www.toyo-mm.co.jp/english/product/spec/417.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

Si-130-6Si-130-6

http://www.toyo-mm.co.jp/english/product/spec/418.htmlhttp://www.toyo-mm.co.jp/english/product/spec/418.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

Si-180-6Si-180-6

http://www.toyo-mm.co.jp/english/product/spec/419.htmlhttp://www.toyo-mm.co.jp/english/product/spec/419.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

*1 By changing the heat barrel, higher pressure setting available.

Si-230-6Si-230-6

http://www.toyo-mm.co.jp/english/product/spec/420.htmlhttp://www.toyo-mm.co.jp/english/product/spec/420.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

*1 By changing the heat barrel, higher pressure setting available.

Si-280-6Si-280-6

http://www.toyo-mm.co.jp/english/product/spec/49.htmlhttp://www.toyo-mm.co.jp/english/product/spec/49.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

Si-350-6Si-350-6

http://www.toyo-mm.co.jp/english/product/spec/421.htmlhttp://www.toyo-mm.co.jp/english/product/spec/421.html

The si-6 series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is maximum settable values.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.