"Si-6S" : 17 results

Si-180-6SSi-180-6S

https://www.toyo-mm.co.jp/english/product/spec/si-180-6s.htmlhttps://www.toyo-mm.co.jp/english/product/spec/si-180-6s.html

The Si-6S series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is a maximum settable value.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

* When set to MAX. injection speed or MAX. pressure, injection stroke. or speed is regulated automatically.

*1 By changing the heat barrel, more higher pressure setting available.

*2 Only wear resistant specification is available for the screw and heat barrel of FH400E, H450E (φ40).

Si-130-6SSi-130-6S

https://www.toyo-mm.co.jp/english/product/spec/4252.htmlhttps://www.toyo-mm.co.jp/english/product/spec/4252.html

The Si-6S series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is a maximum settable value.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

* When set to MAX. injection speed or MAX. pressure, injection stroke. or speed is regulated automatically.

* Only wear resistant specification is available for the screw and heat barrel of DH300E, FH400E.

Si-100-6SSi-100-6S

https://www.toyo-mm.co.jp/english/product/spec/4253.htmlhttps://www.toyo-mm.co.jp/english/product/spec/4253.html

The Si-6S series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is a maximum settable value.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

* When set to MAX. injection speed or MAX. pressure, injection stroke. or speed is regulated automatically.

* Only wear resistant specification is available for the screw and heat barrel of D150HE (CH300E), DH300E, CH450E.

Si-80-6SSi-80-6S

https://www.toyo-mm.co.jp/english/product/spec/si-80-6s.htmlhttps://www.toyo-mm.co.jp/english/product/spec/si-80-6s.html

The Si-6S series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure is a maximum settable value.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

* When set to MAX. injection speed or MAX. pressure, injection stroke. or speed is regulated automatically.

* Only wear resistant specification is available for the screw and heat barrel of D150HE (CH300E), DH300E.

Si-50-6SSi-50-6S

https://www.toyo-mm.co.jp/english/product/spec/si-50-6s.htmlhttps://www.toyo-mm.co.jp/english/product/spec/si-50-6s.html

The Si-6S series provides a SMART solution to ever-complicated injection molding process.

Photographs in the catalog include optional devices.

For the improvement of the product, the appearance and specification are subject to change without notice.

Specifications are expressed in SI units : 1MPa=10.2kgf/cm2, 1kN=0.102tonf

Maximum injection pressure a maximum settable value.

Maximum injection pressure may be limited by the molding conditions and the cycle time.

Maximum injection speed is calculated values. This value may be limited by the setting of injecting pressures.

* When set to MAX. injection speed or MAX. pressure, injection stroke. or speed is regulated automatically.

* Only wear resistant specification is available for the screw and heat barrel of B55E(φ16), BH150E, D150HE (CH300E), DH300E.

TOYO Original Technology Plasticization Items

https://www.toyo-mm.co.jp/english/tec/tec-p02-2.html
A diversity of screws (optional) * SAG design Gas suppressing screw APPLICATION Suppressing Outgassing EFFECT Read more...

Products / Technology

https://www.toyo-mm.co.jp/english/pro/
Plastics Injection Molding Machine Die-Casting Machine